GOST 31336-2006
ГОСТ 31336-2006
|
|
Noise of machines. Engineering methods for measurement of noise of compressors and vacuum pumps
Шум машин. Технические методы измерения шума компрессоров и вакуумных насосов
Status: Effective
The standard establishes methods for measuring the sound radiation of mobile and stationary compressors and vacuum pumps and stating the values of their noise characteristics. The standard establishes the requirements for installation, load and mode of operation of machines during testing and the following noise characteristics: sound power level at a given mode of operation; sound pressure level of radiation in the workplace at a given mode of operation. The standard applies to the following machines: gas compressors (for various gases); oil lubricated air compressors; oil filled air compressors; water filled air compressors; oil free air compressors; gas compressors for hazardous gases; oxygen compressors; acetylene compressors; high pressure compressors (over 4MPa (40 bar); compressors for low suction temperatures (below 0 degrees C); large compressors (power consumption is more than 1000 kW); mobile air compressors and air compressors on skids; rotary blowers, centrifugal fans exhaust fans for pressure <= 0.2 MPa (<= 2 bar). The standard does not apply to: gas compressors (except acetylene) with a maximum permissible operating pressure less than 0.05 MPa (0.5 bar); refrigeration compressors of cooling systems or heat pumps portable portable compressors
Стандарт устанавливает методы измерения звукового излучения передвижных и стационарных компрессоров и вакуумных насосов и заявления значений их шумовых характеристик. Стандарт устанавливает требования к монтажу, нагрузке и режиму работы машин при испытаниях и следующие шумовые характеристики: уровень звуковой мощности на заданном режиме работы; уровень звукового давления излучения на рабочем месте на заданном режиме работы. Стандарт распространяется на следующие машины: газовые компрессоры (для различных газов); маслосмазываемые воздушные компрессоры; маслозаполненные воздушные компрессоры; водозаполненные воздушные компрессоры; бессмазочные воздушные компрессоры; газовые компрессоры для опасных газов; кислородные компрессоры; компрессоры для ацетилена; компрессоры высокого давления (свыше 4МПа (40 бар); компрессоры для низких температур на всасывании (ниже 0 град. С); крупные компрессоры (потребляемая мощность более 1000 кВт); передвижные воздушные компрессоры и воздушные компрессоры на салазках; роторные воздуходувки, центробежные вентиляторы и вытяжные вентиляторы для давления <= 0,2 МПа (<= 2 бар). Стандарт не распространяется на: газовые компрессоры (кроме ацетилена) с максимально допустимым рабочим давлением менее 0,05 МПа (0,5 бар); холодильные компрессоры систем охлаждения или тепловых насосов; портативные переносные компрессоры
Choose Language:
Format: Electronic (pdf/doc)
Page Count: 23
Approved: Federal Agency for Technical Regulation and Metrology,
6/5/2007
SKU: RUSS68184
The Product is Contained in the Following Classifiers:
Construction (Max) »
Standards »
Other state standards used in construction »
17 Metrology and measurements. Physical phenomena »
Construction (Max) »
Standards »
Other state standards used in construction »
23 Hydraulic and pneumatic systems and components for general use. »
Evidence base (TR CU, Technical Regulation of the Customs Union) »
010/2011 TR CU. On safety of machinery and equipment »
Regulations and standards (to ТР ТС ТС 010/2011) »
PromExpert »
SECTION III. LABOR PROTECTION AND SAFETY »
II Industrial sanitation and occupational health »
5 Protection against mechanical vibrations »
5.2 Acoustic noise »
PromExpert »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
4 Testing and control of products »
4.13 Testing and control of products of engineering industry »
4.13.1 Machinery, equipment and components for general engineering applications »
4.13.1.3 Pumps and compressor equipment »
ISO classifier »
17 METROLOGY AND MEASUREMENTS. PHYSICAL PHENOMENA »
17.140 Acoustics and acoustic measurements »
17.140.20 Noise from machinery and equipment »
National standards »
17 METROLOGY AND MEASUREMENTS. PHYSICAL PHENOMENA »
17.140 Acoustics and acoustic measurements »
17.140.20 Noise from machinery and equipment »
ISO classifier »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.140 Compressors and pneumatic machines »
National standards »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.140 Compressors and pneumatic machines »
National Standards for KGS (State Standards Classification) »
Latest edition »
T General technical and organizational and methodological standards »
T3 Physics and Mechanics »
T34 Oscillatory and wave-like movements. Bodies vibration. Sound. Acoustics »
The Document References:
GOST 1.0-92: State System for Standardization of Russian Federation. Basic principles
GOST 1.2-97: Interstate system for standardization. Interstate standards, rules and recommendations on interstate standardization. Procedure for development, taking over application, renovation and cancellation
GOST 12.2.016.1-91: Compressor equipment
GOST 12.2.016.2-91: Compressor equipment
GOST 12.2.016.3-91: Compressor equipment
GOST 12.2.016.4-91: Compressor equipment
GOST 12.2.016.5-91: Compressor equipment
GOST 17187-81: Noise meters
GOST 27408-87: Noise. Methods for statistical processing of data in determination and control of machine emitted noise level
GOST 30457-97: Acoustics. Determination of sound power levels of noise sources using sound intensity. Measurement at discrete points. Engineering method
GOST 30691-2001: Noise of machines. Declaration and verification of noise emission values
GOST 30720-2001: Noise of machines. Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level
GOST 31169-2003: Noise of machines. Measurement of emission sound pressure levels at a work station and at other specified positions. Survey method in situ
GOST 31172-2003: Noise of machines. Measurement of emission sound pressure levels at a work station and at other specified positions. Engineering method in an essentially free field over a reflecting plane
GOST 31252-2004: Noise of machines. Guidelines for the selection of method for the determination of sound power levels
GOST 31275-2002: Noise of machinery. Determination of sound power levels of noise sources using sound pressure method. Engineering method in an essentially free sound field over a reflecting plane
GOST R 51401-99: Noise of machines. Determination of sound power levels of noise sources using sound pressure. Engineering method in an essentially free field over a reflecting plane
|
Customers Who Viewed This Item Also Viewed:
 |
Special railway rolling stok. Dynamic and strength testing procedures
Language: English |
Blanks for marine shafts and rudder stocks. Specifications
Language: English |
 |
|
YOUR ORDERING MADE EASY!
AzerbaijanLaws.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience.
Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfill. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
